. How do I check what software versions are installed on my AFS display?. To check the software versions installed on your AFS display, go to Home Diagnostics Version. You can check the versions installed on any CAN device by going to Home Diagnostics CAN and finding the device in the list. What do I need to connect a Raven controller to my AFS Display?.
Please contact your dealer to ensure that the appropriate software is loaded to your AFS display. Additional cabling required is required. The power/data cable (P/N 87732647) is available from your Case IH dealer. A Raven null modem cable will need to be sourced from Raven. If you are using a 100 series Raven controller (440, 460, etc), use Raven null modem P/N 115-0159-822.
If you are using a 1000 series Raven controller (4000, 4600, etc), use Raven null modem P/N 115-0171-395. Why isn't my prescription showing up in the AFS display?.
There are multiple reasons why the prescription may not show in your AFS display. First, verify that you only have one (1) '.cn1' folder on the data card. The AFS display will only read a single.cn1 folder. When you export a prescription from the desktop software, make sure to backup the existing.cn1 folder that is on the data card, and then delete the existing.cn1 folder from the data card before placing the new.cn1 folder onto the data card. Next, verify that there are not duplicate Grower/Farm/Field names in the AFS Pro 700 display. The prescription is only stored under a single Grower/Farm/Field. Go to Home Performace Profile and touch in the Grower box.
If there are multiple Growers with the same name, try selecting each individualy to see if the prescription shows under any of them. The prescription must match the product form of your controller.
For example, when using a prescription for planting, the prescription must be exported as a planting prescription, or when using a prescription for liquid application, the prescription must be exported as a liquid or spraying prescription. If the prescription form and the controller form are not the same, the prescription will not be available for use. Check that your Work Condition setup is correct. Go to Home Work Condition Layer.
Make sure that the correct controller is assigned to a layer and a product is assigned to the same layer. Also make sure that there are no errors (an ERR button above the product or layer box). How do I subscribe or renew my subscription for for AFS Customer Support?.
To subscribe or renew your subscription for AFS Customer Support, please contact your dealer. How to I output GPS from my AFS display to another system?. The recommended way to output GPS is through the NAV-II controller. A power/data cable will be required and is available from your dealer (P/N 380002422).
This cable will plug into the diagnostic connector located on the NAV-II harness. The other end of the cable will be connected to the system you are sending GPS to.
Once connected, configure the needed NMEA strings by going to Home Toolbox NAV and using the NMEA Output Setup and NMEA Message Setup buttons in the AFS display. The settings will be dependant on what device you are connecting to and can be obtained from the device manufacturer. I have an ISO implement that I am running with my display. If I want to use a prescription for variable rate application, what format should I write it in?. To use a prescription with an ISO implement, the prescription will need to be written in ISOXML format. A TASKDATA folder must be placed on the data card along with your existing.cn1 folder.
I am getting error “AG-060 Cannot engage Automatic” when I attempt to engage AccuGuide on my combine. How can I fix this?. AccuGuide is not enabled. Ensure the “AccuGuide enable switch” or “AccuGuide master switch” is in the enabled position. What happened to the distance calibration on my combine? Where do I find it?. Beginning with version 27 software for Axial Flow combines, the distance calibration is called 'Tire Radius.'
You can find it from the home screen by selecting the 'Calibrations' page, then select the 'Calibr' tab at the bottom of the screen. From the dropdown menu, select 'Tire Radius.' . How do I delete my data?. Prior to deleting any data from your display, make sure that any data you want to keep has been backed up on another device. To delete data from your AFS display, go to Home Data Management Delete. Select the data type you would like to delete from the dropdown menu.
Next, select the specific data you would like to delete from the additional drop down menus. For example, choosing 'Grower' will delete all data stored under that grower (farms, fields, prescriptions, guidance lines, etc.). Once the you have made the desired selection, press the Delete button and confirm that you want to delete the data.Note: if you have your data card in your display when deleting data, it will remove the data from both the data card and the display. If you do not have the data card in the display when deleting data, the data will only be deleted from the display. How do I import my Growers, Farms, and Fields into my AFS display?. If a removable memory device was used in the display to collect data, then the growers, farms, and fields will automatically import into the display on their own once the memory device is inserted into the display.
I'm getting a 'Memory Device Not Detected' error. Insert a memory device into the display. If a memory device is inserted into the display, and this error still occurs, remove the memory device and reformat it on your desktop computer. To do this, insert the card into the computer, or external card reader, and go to My Computer.
Find the memory device, right click, select format, and select Fat 32. Is a data card needed during operation with any CNH display or can I just get the data after the season is over?. Mapping data is only stored when the data card is inserted and recognized by the display. If the data card is not in the display during operation no maps will be recorded. Once I have calibrated my machine I should never have to do it again right?.
Calibrations need to be performed at the beginning of a season or when there is a changed in the operational conditions. I have an ISO implement that is capable of section control, but section control will not work. With an ISO implement, ISO Task Controller is required for section control, variable rate control (with prescriptions), and mapping.
Why will my prescriptions not import into my display while running Task Controller?. Make sure the prescriptions are in the.xml format and exported to the USB with the.cn1 folder.
If the.xml file is not present, the display will not read the prescription for Task Controller. I cannot change my grower, farm, and field name in my display while running Task Controller. The Task Controller screens override the performance profile screens. When running task controller, the changes must be made in the task controller windows. What cables do I need to connect an FM1000 to a Pro 700?.
ZTN67091 (port replicator) & ZTN59043 (null modem cable). ZTN67091 is a port replicator that will plug into the back of the FM 1000. From there, the ZTN59043 will plug into the 67091 and into the Pro 700. ZTN59043 is a null modem cable. I have an ISO implement and would like to use prescriptions, section control or record data.
What do I need to run it on a Pro 700?. Please contact your dealer to ensure that the appropriate software is loaded to your display. The ISO Task Controller activation code will also be required. I am getting error “AG-060 Cannot engage Automatic' when I attempt to engage the AccuGuide on my tractor.
AccuGuide is not enabled. Ensure the “Autoguidance disable switch” or “Roading switch” is in the enabled position. Where do I set my rear offset for my 500T disk drill?. The rear offset is configured through the Virtual Terminal. Select 'Setup' from the main VT screen, then arrow down twice and select PF. Rear offset is displayed as 'Tool Rear Offset'.
Case Ih Pro 600 Monitor Manual
Keep in mind to enter a positive number here as it is asking for the rear offset. Whenever I use AccuControl to apply anhydrous, the toolbar is over-applying.
Why is this happening and how can I fix it?. The target rate and applied rate are for actual nitrogen. When using NH3, 82% is actually nitrogen. This means that if the target rate is entered as 180 lbs, the applied rate will be 180 lbs of actual nitrogen, but 220 lbs of total NH3 will be applied. To calculate the total NH3 from the actual nitrogen, multiply the actual nitrogen value by 1.22. To calculate the actual nitrogen from the total NH3, multiply the total NH3 value by 0.82.
What are the criteria that must be met before a combine can begin monitoring / recording yield? Header is in work mode. This is indicated by a green arrow pointing down in the status warning area. 2. Ground speed above.5 mph.
3. Elevator speed between 250-599 RPM. 4.
Data card/USB is inserted in the monitor. 5. Create a Grower / Farm / Field / Task. My Cotton Picker Yield sensor is reading yield even when not operating or not reading a value when there is flow. How can I troubleshoot this? Go to Cal Sensor: Raw Flow should be changing when there is crop in the unit and at or near zero when there is no flow.
2. If Raw Flow IS reading when there is NOT flow: Increase the sensor sensitivity value.
3. If Raw Flow is NOT reading when there IS flow: decrease the sensor sensitivity value. 4.
Complete steps 2 and 3 for each sensor. How do I know what features are activated in my display?. Go to Toolbox Activate. This screen lists all activations currently installed on the display. It will not include receiver activations. This is also the screen where purchased activation codes are entered.
Where do I enter an activation code for my AFS GPS receiver?. Go to Toolbox GPS. Page down to the “Activation” box. This is where GPS receiver activations are entered.
This feature is available in displays with version 28 and higher software installed. I'm not sure what software versions are installed on my display. Where can I check this?. Go to the home screen. Select Diagnostics, then the Version tab.
This tab contains a list of software currently running on the display. This list does not include firmware for the GPS receiver or the NAV II controller. My moisture value isn’t changing on my screen even though I am in changing moisture conditions. What can I check?. With the key off:. Check the fuse for the moisture bypass unit.
Remove the two pins at the bottom of the bypass auger to check that the auger is not plugged. Contact your dealer for additional help if needed.
My Yield (Wet Bushels Per Acre) reads -. There are three main things that are considered when the display calculates Wet Bushels Per Acre. If the display is reading dashes, you are missing one of the following:. Weight, Wet.
Working Width (Greater than 0). Ground Speed The above user defined windows can be set up in a run screen by going to Toolbox Layout. My Yield (Dry Bushels Per Acre) reads -. There are five main things that are considered when the display calculates Dry Bushels Per Acre Yield.
If the display is reading dashes, you are missing one of the following:. Weight, Wet. Crop Moisture. Crop Trade Moisture ( Set in Calibrations Crop). Working Width (Greater than 0). Ground Speed The above user defined windows can be set up in the run screen by going to Toolbox Layout.
My Moisture is reading constant and is the same as my Manual Moisture Setting in Calibrations Crop. If your moisture in the display is reading the same as the manual moisture setting in calibrations crop, it is because the moisture sensor is in manual mode.
Go to Toolbox Layout and add Moisture Mode to a run Screen. With Moisture Mode you can turn Manual Moisture to Auto Mode. Moisture will be in Set to Manual Mode when the moisture sensor detects a invalid reading, a moisture sensor fault is detected, or if the operator turns manual moisture mode on. On V28.8 Yield software and after, the display will identify in the Status and Warning Icon area a Man Moisture Icon to signify that the moisture sensor detects an invalid reading. This is often seen when keying on the machine at the beginning of operation until crop enters the Moisture Bypass Assembly. How do I change what I see on my run screens in my Pro300, Pro600, or Pro700 display?.
The windows on the run screens are referred to as User Defined Windows. You can create your own layout by going to Toolbox Layout. Create a new layout (recommend using operator's name). The run screens 1-6 can be set up by selecting a window and scrolling through the list to select the intended window to be viewed. My acreage is off for my harvested field.
How do I correct this?. Often the Acreage shown as harvested is not the same as what was planted or what the known field size is. It is recommended to do a Distance Calibration or Tire Radius (Found in Calibrations Calibrate), to correct the wheel speed sensor for the tires installed on the Combine. Several in season factors can attribute to the acreage being a mismatch after a field is finished. The measured area for the harvested field can be corrected by going to Calibrations Area tab. There you can select the Grower, Farm and Field and correct the actual acres harvested to what is recorded.
I'm not sure what version my NAV II or GPS Reciever software is on. Where can I check this?.
Go to Diagnostics CAN tab. This tab will list every controller on the vehicle, and controller information includes what software version each one is on. The controller name for the NAV II is 'NAV II' and for the GPS Reciever is 'GPS'. The version listed next to 'Software Version' is the software version installed in the controller.
If the controller is coming up as 'Not Detected', contact your dealer for further troubleshooting. What size removable memory device should I use in my display?. It is recommended to use the 4GB removable memory device available through your Case IH dealer.
Do not use a removable memory device larger than 4GB in the display. I would like to record an as-applied map for a product not controlled by my display. How can I set this up?
Go to ToolboxManual and create a ManApp. The implement section widths, forward offset, and right offset will need to be entered. Go to ToolboxProduct and create a product. Go to Work ConditionLayer and create a work condition.
Assign the ManApp and product to a layer. When using Large Tractor or Medium Tractor software go to Toolbox Implement and configure the implement to Hitch (if it is a hitch implement) or EHR#.
NOTE: IF THE IMPLEMENT NEEDS VARIABLE DEPTHS, DO NOT USE THE EHR THAT IS CONTROLLING THE DEPTH OF THE IMPLEMENT. 5. To trigger coverage mapping when an EHR is selected, push the selected EHR to the detent. When the EHR is detented, the work arrow should change from pointing up to pointing down. If all other conditions for the unit to be in work are met, the down arrow will be green. When a hitch implement is selected the work state arrow will change when the 3-point hitch is raised and lowered.
To turn off coverage mapping when an EHR implement is selected, pull the EHR back until it detents again. The work arrow will change from pointing down to pointing up, and from green to grey. Why is my work arrow not changing when I am running my 500T with Task Controller?. The work state arrow in the Status and Warning Icon area needs to have three conditions met to change. 1. The implement must be lowered.
You must be moving. The meters must be turning.
If any of the three conditions are not being met, contact your dealer for service. How do I calibrate guidance in my 2016 (or newer) Steiger?. For model year 2016, Steigers are now sold with Advanced steering technology. The only calibration required is the roll angle calibration. What is the highest version software I can use for my 1200 series Early Riser planter?. For 1200 series Early Riser planter models (or any planter with MIU or MCC controllers), version 27 software is the highest that can be used.
If you have a newer version please contact your dealer. Controller types for your planter can be seen in the Diagnostics menu on the CAN tab.
Can I use my AFS Pro 700 for soil sampling?. The Pro 700 does not support soil sampling features. The workaround for this is when scouting with the display, mark an obstacle or a rock at the sample locations. These field marks will then come through in the desktop software.
This also works creating obstacles or features in the Desktop Software and exporting to the display to show where to dig. Can I rename my run screens?. In the Toolbox Layout screen where User Defined Windows are selected, there is a new selection called 'Run Tab Name'. Tap on this window to access the pop-up keyboard. Names should be kept to 8 characters or less to display properly on the run screens. Note: This feature is available with Framework 30.4.0.0 or higher.
Does the Pro 700 save data to the internal memory of the display?. The AFS Pro 700 display does not save all data to the internal memory. To save mapping data, a.
The following manuals are currently available for version 26. software. AFS Pro 600/700 Operators Manual: 84301850. AFS Pro 600/700 Planter Operators Manual: 84402176.
AFS Pro 600/700 AccuGuide/All-Makes/RowGuide Operators Manual: 84304846. AFS Pro 600/700 AccuGuide Quick Reference Card: 84305197. AFS Pro 600/700 Patriot Sprayer Quick Reference Card: 84422012 All manuals may be ordered from your. Add a '-CD' to the part number to order the manual in PDF form on CD media. So-for this statement it looks like I can't get om's online? They change so darn frequently that it's a waste of money to get a new OM every time there is a software change.
I guess I'm just used to John Deere's way of putting the OM's out on Stellar Support, when updates come out they get updated and you can just redownload them as a PDF to your computer for free. I would really rather have the Pro 600 manuals in pdf form than a hard copy so if anyone can lead me in the right direction on if I can even find them online it would GREATLY help me out! Oh another thing-has anyone come across a true simulator of the AFS Pro600. I don't mean tutorials that will walk you thru how to set something up, but a true simulator were I can have full capability to punch around the buttons and go where I want to go on the 600.
Sandhoff: 3/31/2011 10:16. torn: 3/31/2011 11:08 Jump to forum:.